Engine Mechanical

Gear Reduction Starter Manual

This gear reduction starter provides higher cranking torque while drawing less current.Specifications:Rotation CCWkW 1.4Gearing 4.44 to 1 gear ratioRotatableVoltage 121.9hp motorFittment:Vanagon and Buses with a manual transmissionAny engine using a...

SCP

10'-12' Subaru EJ25 Accessory Belt

If your accesory belt is worn and/or cracked it's time to replace it. Get one now!   Fitment: 2010-2012 EJ25 Subaru Engines With alternator and AC compressor With alternator and power steering pump With alternator, power steering pump, AC...

Intake Manifold Gasket: Subaru 2.2L

These intake gaskets should be replaced whenever the intake manifold is removed and reinstalled.Fits the following Subaru engines:1990-1998 2.2LSold individually. Two are required per engine.

Intake Manifold Gasket: Subaru 2.5L DOHC

These intake gaskets should be replaced whenever the intake manifold is removed and reinstalled.Fits the following Subaru engines:2.5L DOHC non-turboSold individually. Two are required per engine.

Timing Belt Guide Subaru M/T

This timing belt guide usually comes on engine installed in Subaru with manual transmission to keep the belt in place during engine braking between shifts or rolled backward in gear. We recommend installing this over the crank pulley if your engine is...

Subaru to Vanagon Automatic Transmission Adapter and Flex Plate

Subaru to Vanagon Automatic Transmission Adapter and Flex Plate Made to exacting standards, this adapter and flex plate come with all the parts needed to bolt the 2.0L, 2.2L, 2.5L, 3.0L, or the 3.3L Subaru engine to any Vanagon automatic transmission...

Subaru Flywheel Bolt

Subaru flywheel bolt. 8 required per flywheel. Subaru Flywheel

Rubber Engine Mount - Outer

  We tested several brands of rubber mounts and discovered that there is a difference between the cheapest and the best. Ours are noticeably quieter than less expensive mounts and we believe they are easily worth the price difference. We think...

SCP

Stage 1 Clutch Kit for SmallCar Bellhousing

Need to do an entire clutch job and are tired of buying all your performance clutch parts separately? Just need everything in one product? Our Clutch Kit for Small Car's Bellhousing is for you. Fitment: Subaru engines up to 150HP (2.2L and...

SCP

Subaru-Vanagon 4 Cyl 2WD Engine Mount Powder Coated

New! Improved design for late Subaru engines - provides more clearance for thermostat housing and water pump. Our mount has the advantage of placing the stock Vanagon rubber mounts at the rear of the engine which drastically reduces engine movement and...

Subaru Cam Seal: Viton

Not to be confused with other brands. Viton Cam Seals will outlast the stock Subaru ones by three to four times. Viton Cam Seals are the only seals we'll use for this area that is prone to leakage.Fitment Notes:1990-2008 normally aspirated Subaru...

SCP

Subaru 4 Cyl-Vanagon 4WD Engine Mount Powder Coated

New! Improved design for late Subaru engines - provides more clearance for thermostat housing and water pump. Our mount has the advantage of placing the stock Vanagon rubber mounts at the rear of the engine which drastically reduces engine movement and...

Crank Seal Subaru Flywheel End: Viton

This crank seal is Viton and will outlast the original 3-4 times.These are the only type of seal we'll use, and they're not easily replaced. Fitment Notes:1990-2008 normally aspirated Subaru engines: 1.8, 2.0, 2.2, 2.5, 3.0, and 3.3L Sold indivually. One...

Flexible Dipstick Kit for Subaru Engines

This kit replaces the stock dipstick and tube with a Teflon lined braided stainless tube with custom made fittings and a flexible dipstick with level indicator - which is made for Small Car's 5qt Oil Pan. With this installed, you can easily check your...

Subaru

Subaru Crank Seal: Viton

Not to be confused with other brands. Viton Crank Seals will outlast the stock Subaru ones by three to four times. Viton Crank Seals are the only seals we'll use for this area that is prone to leakage.Fitment Notes:1990-2008 normally aspirated Subaru...

Intake Manifold Gasket: Subaru 1999-Later

These intake gaskets should be replaced whenever the intake manifold is removed and reinstalled.Fits the following Subaru engines:2.2L: 1999-2001 Legacy 2.5L Non-Turbo: 1999-2009 Forester 2.5L Non-Turbo:1999-2010 Impreza 2.5L Non-Turbo:1999-2011 Sold as...

Subaru

Piston Ring Set 2.5L SOHC Subaru

We have been able to source Subaru rings from the OE manufacturer. We guarantee these rings to be equal to the original replacement rings and to incorporate the latest design specifications. This set fits the following engines: Subaru Baja 2003-2006 2...

Nylon Hose Adapters

These nylon 12 mm or 1/2" hose fittings are very useful when connecting the Subaru engine breather hoses.For those working on later Subaru engines, you will find that there are too many engine hoses and not enough fittings at the filter housing. Also,...

Hose Menders: Brass

These durable hose menders are useful for various tasks in an engine conversion.Sizes available are as follows:8 x 8mm: useful for splicing fuel hoses - especially for a Syncro Vanagon5/8" x 5/8": for splicing heater hoses - in front or rear.3/8" x 1/2":...

Fuel Injection Fuel Hose: 5/16"

This 5/16" fuel hose fits the Subaru and the Vanagon fuel fittings. Sold per inch so you can order order the exact length you need. For the safest fuel line connections we recommend you use our fuel hose crimp clamps. Make sure to properly...

Steel Header Flange

Used with Small Car's Stainless Steel Header.Specifications:3/8" thick steel(3) 2" bolt holes with long end for extra support

SCP

Tachometer Face (Black) 8K RPM

8,000 RPM tachometer face with precut shape and mounting holes. Also available in 7,000 RPM (shown). Installation Instructions

SCP

Tachometer Face (Black) 7K RPM

7,000 RPM tachometer face with precut shape and mounting holes. Also available in 8,000 RPM. Installation Instructions

Stainless Steel Muffler Brackets

These stainless brackets are specially designed to work with Small Car's engine mounts to hold the muffler rigidly to the engine assembly and very close to the stock position. Used in one position for the Syncro and oppositely for the 2WD...