Parts

SCP

Throttle Body Reverser: T2, Bus

Small Car is proud to introduce the Throttle Body Reverser to our portfolio of products.  This product is designed for all years Subaru EJ22 and EJ25.  It will accomodate both Drive-by-wire throttle bodies and cable drawn units without any...

Oxygen Sensor Pair 05'-12'

This kit includes the rear oxygen sensor and the front A/F sensor needed for an 2005' to 2010' EJ25. We highly reccomend replacing these sensors when installing a Subaru engine in your van. Please specify the model and year of your engine when...

Stainless Muffler Clamp: 5.25"

This clamp is made with heavy duty 14 gauge stainless steel and is much tougher than other brands.Fits:1980-1985 stock Vanagon mufflers Sold individually. Two are required.

Stainless Muffler Clamp: 5.75"

This clamp is made with heavy duty 14 gauge stainless steel and is much tougher than other brands. Fits: Stock Vanagon OE Muffler: 1986-1991  SCP's Stainless Steel Muffler Please Note: This clamp will NOT directly attach to the...

Stainless Muffler Clamp: 6"

This clamp is made with heavy duty 14 gauge stainless steel and is much tougher than other brands.Fits:Small Car's 2" Performance MufflerSmall Car's 2 ¼” Performance MufflerSold individually. Two are required.

Stainless Steel Muffler Brackets

These stainless brackets are specially designed to work with Small Car's engine mounts to hold the muffler rigidly to the engine assembly and very close to the stock position. Used in one position for the Syncro and oppositely for the 2WD...

2" Three Bolt Exhaust Flange

Made from 3/8” thick stainless steel, this flange has a 51mm (2") center hole and is beveled on one side so it can be installed to accept a 2" Exhaust Flange Gasket or a metal O-Ring Seal (linked below). Additionally, the mounting...

Header Gasket Subaru: Dual Port 2.2 & 2.5

Gasket for Subaru 2.2L Dual Port and 2.5L header - including turbo.Exhaust header to head gasket.Sold individually. Two are required.

Vanagon Exhaust O-Ring

Exhaust O-Ring fits the stock Vanagon exhaust collector "J" pipe and the "J" pipe to the stock catalytic converter or Small Car's Stainless Steel Catalytic Converter.Sold individually. Two are required.

Stainless Steel Exhaust Nut & Bolt Kit

A complete stainless nut and capscrew set for your Vanagon exhaust. Kit includes hardware for the following: Collector or "J" pipe to stock exhaust manifold or Small Car's Subagon header "J" pipe to catalytic converter  Catalytic convertor to...

2" Exhaust Flange Gasket

This high quality metal faced exhaust gasket fits Vanagons and Type IIs. The slotted mounting holes allow a proper fit for both the mufflers and tailpipes that have a slightly different bolt pattern. The inside hole dimension is 52mm or approximately 2...

2 1/4" Exhaust Flange Gasket

Three bolt reinforced metal gasket for the 2-1/4" Exhaust Flange.

SCP

Exhaust Flange: Three Bolt 2 1/4"

Designed to match the 3.3L header, this three bolt 3/8" stainless steel flange is sized to fit over a 2 1/4" pipe and bolt to the header output. You will also need Flange Gaskets (linked below).   Sold individually.

Subaru

Header Gasket: Subaru 3.3L SVX

Gasket for Subaru 3.3L SVX header. Exhaust header to head gasket.Sold individually. Two are required.

Header Gasket Subaru: 2.2: 1996-Later

Gasket for Subaru 2.2L single port header. Exhaust header to head gasket.Sold individually. Two are required.

SCP

Turbo Header Output Flange

Laser cut from 3/8" steel, this 5 bolt flange takes a 2 1/4" pipe and fits the turbo output on the 2.2 and 2.0L Subaru engines.

SCP

Turbo Header Up Pipe Flange

Laser cut from 3/8" steel, this 2" 5 bolt flange fits on the header up pipe where it meets the turbo. Fits the Subaru 2.2 and 2.0L turbo engines.