Parts

ScanGauge

ScanGauge Cable

Use this cable to allow your ScanGauge II or ScanGauge III tool to work in an extra vehicle without removing your original cable.Most applications like Vanagons and Buses will require a cable extender. Get that here. 

Subaru Cam Seal: Viton

Not to be confused with other brands. Viton Cam Seals will outlast the stock Subaru ones by three to four times. Viton Cam Seals are the only seals we'll use for this area that is prone to leakage.Fitment Notes:1990-2008 normally aspirated Subaru...

Timing Belt Roller: Subaru 1990-Later

This timing belt roller is used on all of Subaru's 2.0, 2.2 and 2.5 engines. Ours is a top quality part from Japan with double roller bearings. A much longer lasting part than the GMB or the single roller NSK that is commonly sold.Sold individually. Two...

Head Gasket Set: 2.2L Subaru EJ22

This head gasket set is from a Subaru original equipment manufacturer.Fits the following engines:Subaru Legacy 2.2L 1990-1998Subaru Impreza 2.2L 1995-1998Kit Contains:2 Head Gaskets4 Exhaust Gaskets (single port not shown)2 Intake Gaskets2 Valve Cover...

Performance Clutch Kit: SVX 5 Speed

This performance clutch kit is the best we've found for the SVX 5 speed conversion. We tried clutches from ACT, Clutchmasters, and a few others and found the pedal pressure to be excessive as well as other problems.You will like the feel and the...

SCP

Subaru 4 Cyl-Vanagon 4WD Engine Mount Powder Coated

New! Improved design for late Subaru engines - provides more clearance for thermostat housing and water pump. Our mount has the advantage of placing the stock Vanagon rubber mounts at the rear of the engine which drastically reduces engine movement and...

Crank Seal Subaru Flywheel End: Viton

This crank seal is Viton and will outlast the original 3-4 times.These are the only type of seal we'll use, and they're not easily replaced. Fitment Notes:1990-2008 normally aspirated Subaru engines: 1.8, 2.0, 2.2, 2.5, 3.0, and 3.3L Sold indivually. One...

Head Gasket Set: EJ25 SOHC

This head set is from the Subaru original equipment manufacturer and has the gaskets you need when replacing rings or head gaskets.Fits the following engines:1998-2005 Impreza RS, TS Outback 2.5L, and the 06-07 2.5i2000-2004 Legacy and Outback 2...

SCP

Stainless Steel Exhaust "J" Pipe

Finally! A stainless steel version of the stock Vanagon collector to catalytic converter pipe. This has loose flanges on both ends and when used with the OE metal o-ring (linked below), it allows more flexibility in muffler and catalytic...

ScanGauge

Cable Extension for ScanGauge

If your OBD2 connector is in the rear and more than six feet away from the dash, this extension cable adds another 20 feet to your cable. In Vanagons this allows you to keep all connections inside the vehicle and out of the elements.Includes necessary...

Subaru

Subaru Crank Seal: Viton

Not to be confused with other brands. Viton Crank Seals will outlast the stock Subaru ones by three to four times. Viton Crank Seals are the only seals we'll use for this area that is prone to leakage.Fitment Notes:1990-2008 normally aspirated Subaru...

Coolant pipe stainless

This heliarc welded stainless coolant pipe is designed to go across the back and the right side of the Vanagon engine bay to allow easy connection of the Subaru coolant outlet to the Vanagon radiator pipe. No coolant manifold alterations are needed when...

Intake Manifold Gasket: Subaru 1999-Later

These intake gaskets should be replaced whenever the intake manifold is removed and reinstalled.Fits the following Subaru engines:2.2L: 1999-2001 Legacy 2.5L Non-Turbo: 1999-2009 Forester 2.5L Non-Turbo:1999-2010 Impreza 2.5L Non-Turbo:1999-2011 Sold as...

Subaru

Piston Ring Set 2.5L SOHC Subaru

We have been able to source Subaru rings from the OE manufacturer. We guarantee these rings to be equal to the original replacement rings and to incorporate the latest design specifications. This set fits the following engines: Subaru Baja 2003-2006 2...

Hose Menders: Brass

These durable hose menders are useful for various tasks in an engine conversion.Sizes available are as follows:8 x 8mm: useful for splicing fuel hoses - especially for a Syncro Vanagon5/8" x 5/8": for splicing heater hoses - in front or rear.3/8" x 1/2":...

Steel Header Flange

Used with Small Car's Stainless Steel Header.Specifications:3/8" thick steel(3) 2" bolt holes with long end for extra support

Vanagon Coolant Reservoir Tank: 1986-1991

Good quality made tank with Blau German Reservoir Cap. This is a reproduction of the stock Vanagon 1986-1991 coolant reservoir tank. Required when using our coolant reservoir bracket with a 1980-1985 Vanagon conversion.

SCP

Subaru EJ22 Power Steering Hose Kit

This hose connects the Subaru power steering pump to the power steering rack on the right side of the engine compartment. Works with four or six cylinder Subaru engines. Some EJ22 power steering pumps have 14 mm outlets and some have 16 mm outlets...

Automatic Accelerator Cable Kit: 8mm (Drive by cable Subaru)

This kit allows the original Subaru throttle cable to be used to connect the Subaru engine to the Vanagon's Automatic transmission. The Vanagon original accelerator pedal to transmission cable will be reused. Kit includes: Bracket that bolts to the side...

Accelerator Cable Kit: Manual Transmission: 8mm

This kit is a complete replacement of the stock manual transmission accelerator cable and includes all parts to connect the Subaru engine to the accelerator pedal. Fitment Notes: 1990-1994 Subaru engines and the SVX have a 6mm barrel at the throttle...

SCP

Tachometer Unit Calibration

The Subaru engine's ECU has a tach output. However, the late model ('86-'91) Vanagon's tachometer is not sensitive enough to pick up this signal. Lucky for you we have a solution! We have altered the circuitry in the tachometer to increase the...

SCP

Vanagon Gauge Face Set (White) - 7K PRM

These white overlays are applied over your original faceplates and are available with a 7,000 or 8,000 max RPM tachometer. All attachment points are precision cut to match your original stock gauges.   Installation Instructions

SCP

Vanagon Gauge Face Set - 8K rpm white

These very nice white overlays are applied over your original faceplates and are available with 7,000 or 8,000 max rpm tachometer. Ours have the tiny square openings for the regular and trip odometers precut as are the fuel and temp gauge faces. Now...

Hall Effect Sensor

Replacement sensor for our Hall Effect Speed Sensor Kit. Installation Instructions