Subaru Conversion Parts

$0.65
This fuel hose is the perfect size to fit the Subaru and the Vanagon fuel fittings. 7mm hose is really too small and 8mm fits too loose. This fuel hose is...
In stock
+

$0.85
Subaru flywheel bolt. 8 required per flywheel. Flywheel
In stock
+

$1.50
These crimp clamps are the OE style stainless with the band going one and one half times around so there is no pinched hose and little chance of fuel...
In stock

$2.25
These 12 mm or 1/2" hose fittings are very useful when connecting up all the breather hoses for the Subaru engines. On later engines especially, there are...
In stock

$4.25
Here is a fine way to distinguish your Vanagon as a repowered VW, or for the Subaru owner who wants to add a bit of bling. The 2.5 DOHC lettering is...
In stock

$3.25
These durable hose menders are useful for various tasks in an engine conversion. Sizes available are as follows. 8X8mm - Useful for splicing fuel...
In stock

$3.95
This high quality metal faced exhaust gasket fits Vanagon and Type II. The slotted mounting holes allow a proper fit for both the mufflers and tailpipes...
In stock
+

$5.50
If you are installing the J pipe in a 1985 or earlier Vanagon and do not have a catalytic converter with a port for the oxygen sensor, you may need to weld...
In stock
+

$5.95
Gasket for Subaru 2.2L dual port and 2.5L header including turbo . Exhaust header to head gasket. Two required.
In stock
+

$6.37
Use to delete oil cooler above the oil filter. For models with oil cooler the cooler must be removed for the conversion.
In stock
+

$6.50
These intake gaskets should be replaced whenever the intake manifold is removed and reinstalled. Fits the following Subaru engines: 2.5L DOHC...
In stock
+

$6.95
These intake gaskets should be replaced whenever the intake manifold is removed and reinstalled. Fits the following Subaru engines: 1999-2001...
In stock
+

$6.95

Exhaust O-ring oring o ring

In stock
+

$6.95
Gasket for Subaru 2.2L single port header. Exhaust header to head gasket. Two required.
In stock
+

$6.95
3 bolt metal reinforced gasket for the 2-1/4 inch flange .
In stock
+

$7.25
These intake gaskets should be replaced whenever the intake manifold is removed and reinstalled. Fits the following Subaru engines: 1990-1998...
In stock
+

$7.69
This is the replacement clutch pilot bearing seal for the Small Car Bellhousing
In stock
+

$8.95
Spacer used for the clutch master cylinder
In stock
+

$9.25
Not to be confused with other brands, these cam seals are Viton and will outlast the originals by 3-4 times. They are the only seals we'll use for this...
In stock
+

$10.25
Not to be confused with other brands, this crank seal is Viton and will outlast the original 3-4 times. These are the only seals we'll use for this area...
In stock
+

$10.95
NEW ITEM This panel set is for the Vanagon gauge cluster to allow the original OXS warning lamp to be used as a check engine light. Necessary for...
In stock

$10.95
NEW ITEM This panel set is for the Vanagon gauge cluster to allow the original OXS warning lamp to be used as a glow plug light, an LED can be added...
In stock
+

$11.95
Ultra Grey Silicone Sealant for oil pans and most other metal to metal sealing jobs.
In stock
+

$11.95
Gasket for Subaru SVX 3.3L header. Exhaust header to head gasket. Two required.
In stock
+

$12.75
This crank seal is Viton and will outlast the original 3-4 times. These are the only type of seal we'll use, and they're not easily replaced. This crank...
In stock
+

$12.95

Clutch Pilot Bearing for Smallcar Bellhousing

In stock
+

$14.25
A/C Belt for Subaru 4 Cylinder.
In stock
+

$14.25
Hose reducer 1 1/2"-1 1/4".
In stock
+

$14.95
Here is a handy accessory outlet that you can install in any number of places to power up your cellphone, laptop, DVD viewer or other 12 volt equipment. It...
In stock
+

$14.95
This coolant level sensor fits the pressurized coolant expansion tank in 1983-1990 Vanagons. MFG Part Number: 251919372  
In stock
+

$15.50
Alternator Belt for 3.3L SVX
In stock
+

$16.00
Replacement sensor for our SSK5 speed sensor kit. SSK5 Instructions
In stock
+

$16.50
Upgrade your SmallCar flexible dipstick to the latest easy to read tubular dipstick. Made with silicone and teflon polymer materials, this cool design was...
In stock

$16.95
If your OBD2 connector is in the rear and more than six feet away from the dash, this extension cable adds another 20 feet to your cable. In Vanagons this...
In stock
+

$17.50
3/8" thick Steel Header Flange. 2" 3 bolt with long end for extra support. Used on our H025 Header.
In stock
+

$17.50
Mount between engine crossmember and frame to lower the engine to clear the Vanagon deck lid. 2wd only. Priced per pair
In stock
+

$17.95
A/C Belt for 3.3L.
In stock
+

$19.25
Metric steel to extend the Syncro skid plate rails - 6" is enough for one Vanagon w/4cyl.
In stock
+

$19.95
8,000 rpm tachometer face with precut shape and mounting holes. Also available in 7,000 rpm shown. Installation instructions
In stock
+

$19.95
7,000 rpm tachometer face with precut shape and mounting holes. Also available in 8,000 rpm. Installation instructions
In stock
+

$20.95
We tested several brands of rubber mounts and discovered that there is a difference between the cheapest and the best. Ours are noticeably quieter than...
In stock
+

$21.95
Use this cable to allow your ScanGauge tool to work in an extra vehicle without removing your original cable.
In stock
+

$24.95
Heavy duty 6" diameter clamp for Vanagon mufflers and our stainless steel brackets. This clamp is made with 14 gauge stainless steel and is much tougher...
In stock
+

$24.95
Heavy duty clamp for Vanagon mufflers. This clamp is made with 14 gauge stainless steel and is much tougher than other brands of clamp. 2 required....
In stock
+

$24.95
Heavy duty clamp for Vanagon mufflers. This clamp is made with 14 gauge stainless steel and is much tougher than other brands of clamp. 2 required. #...
In stock
+

$24.95
We tested several brands of rubber mounts and discovered that there is a difference between the cheapest and the best. Ours are noticeably quieter than...
In stock
+

$27.25
NEW ITEM ! A complete stainless nut and capscrew set for your Vanagon exhaust. This kit has hardware for the following: Collector or "J" pipe to stock...
In stock
+

$27.25
Laser cut from 3/8" steel, this 2" 5 bolt flange fits on the header up pipe where it meets the turbo. Fits the Subaru 2.2 and 2.0L turbo engines.
On backorder
+

$27.50
Designed to match the 3.3L header, this 3 bolt 3/8" stainless steel flange is sized to fit over a 2 1/4" pipe and bolt to the header output. Flange...
In stock
+

$27.50
This flange is stainless, 3/8" thick material and has a 51mm (2") center hole and is beveled on one side so it can be installed to accept a gasket or...
In stock
+

$27.50
Laser cut from 3/8" steel, this 5 bolt flange takes a 2 1/4" pipe and fits the turbo output on the 2.2 and 2.0L Subaru engines.
Out of stock

$27.50
2" aluminized 3.00" radius 180 degree mandrel bend, short.
In stock
+

$29.95
Want to build your own header? Maybe you are building a flying boat or a 3.3L powered Borgward. Flange is laser cut from 3/8" steel and can accept up to 1...
On backorder
+

$36.95
High amperage 12v relay kit for EE20 SC ECU or glow plugs. Includes relay and socket with wire terminals. One kit required for ECU and one for the glow...
In stock
+

$38.95
We designed this to bolt directly to the stock air cleaner mount on the right side firewall that formerly held the air cleaner assembly. It keeps the...
In stock
+

$40.00
Single-Wall, 15-degree Angle-Cut, Rolled-Edge. Diameter: 3" I.D. Inlet: 2.25" Length: 7"
In stock
+

$43.95
Accelerator Cable Kit 8mm- automatic transmission Vanagons   This kit allows the original Subaru throttle cable to be used to connect the Subaru...
In stock

$43.95
Accelerator Cable Kit 6mm - automatic transmission Vanagons   This kit allows the original Subaru throttle cable to be used to connect the Subaru...
In stock

$49.95
These very nice white overlays are applied over your original faceplates and are available with 7,000 or 8,000 max rpm tachometer. Ours have all the little...
In stock

$49.95
These very nice white overlays are applied over your original faceplates and are available with 7,000 or 8,000 max rpm tachometer. Ours have the tiny...
In stock

$49.95
Metric steel to extend the Syncro skid plate rails - 16" is needed for 3.3L engines.
In stock
+

$55.00
NEW ! Tired of your VW Bus or Vanagon's tailpipe rusting out or drooping at a wierd angle? This polished stainless tailpipe is mandrel bent and has...
In stock
+

$55.00
Coolant reservoir tank Vanagon 86-91. Required when using our coolant reservoir bracket with -85 Vanagon conversion. German made tank with German Blau cap.
In stock
+

$56.00
The Subaru engines ECU has a tach output. The Vanagon tach from 1986-1991 is not sensitive enough to pick up this signal so a solution must be found to...
In stock

$59.95
Accelerator Cable Kit 8mm - manual transmission 8mm Complete kit from the pedal in front to the Subaru engine in the back, similar to a stock...
In stock
+

$59.95
Accelerator Cable Kit - manual transmission 6mm Complete kit from the pedal in front to the Subaru engine in the back, similar to a stock replacement...
In stock
+

$59.95
Use this kit to mount the Subaru drive by wire pedal on the engine. Required for drive by wire engine conversion in an automatic Vanagon. This kit is...
In stock

$59.95
All the OBD2 engines from 1996 on require a vehicle speed sensor. The engines up to 1995 can also benefit from an SSK5, most conversions idle and perform...
In stock

$65.00
Use this kit with the original Vanagon cable bracket to mount the Subaru drive by wire pedal on the firewall of a 2wd manual Vanagon. Required for drive by...
In stock

$65.95
Intake hose kit This hose kit is for 2000 and later normally aspirated 2.5L engines. We use these parts to connect the throttle body to the original...
In stock
+

$65.95
2 1/4" 409 stainless steel 3.00" radius 180 degree mandrel bend, short.
In stock
+

$74.95
These stainless brackets are specially designed to work with the Smallcar mount to hold the muffler rigidly to the engine assembly. Used in one position...
In stock
+

$75.00
Alert! A $10 discount is available when purchasing with a conversion kit or harness modification kit. This interface board is for 1996 and later...
In stock
+

$79.00
We have been able to source Subaru rings from the OE manufacturer. We guarantee these rings to be equal to the original replacement rings and to...
In stock
+

$85.00
NOW with tubular dipstick for easier reading, and available for the 3.3L SVX engine! No more shifting your luggage and lifting the engine lid...
In stock

$85.00
Vanagon - Subaru Power Steering Pressure Hose - 4 or 6 Cylinder This hose attaches directly to the Subaru power steering pump and connects to the...
In stock

$85.00
Uni-Directional Battery Separator by Sure Power The Battery Separator Smart Solenoid Charge Priority System offers... Simple installation--Connects...
In stock
+

$98.95
Use this kit to mount the Subaru drive by wire pedal on the engine. Required for drive by wire engine conversion in a 2wd or 4wd manual Vanagon....
In stock

$98.95
Use this kit to mount the Subaru drive by wire pedal behind the passenger side tail light. Required for drive by wire engine conversion in a manual...
In stock

$105.00
Collector or "J" pipe-Stainless Finally! A stainless version of the stock Vanagon collector to cat pipe. Fits between the stock 1986 and later...
In stock
+

$109.00
Replacement disc for stock Vanagon clutch and our clutch for our bellhousing.
In stock
+

$109.95
This heliarc welded stainless coolant pipe is designed to go across the back and the right side of the Vanagon engine bay to allow easy connection of the...
In stock
+

$129.00
Quiet Vanagon - Subaru Power Steering Pressure Hose - 4 or 6 Cylinder This hose attaches directly to the Subaru power steering pump and connects to...
In stock

$129.95
The variable valve timing Subaru engine do not have a fuel pressure regulator attached to the fuel rail so a regulator is needed to achieve the fuel...
In stock
+

$135.00
This kit enables a person with some wiring ability and lots of time to take a Subaru "bulkhead" wiring harness, remove a large number of connectors and...
In stock

$139.95
This high flow cat is 2 1/4" in and out and is very compact allowing it to be installed between the header and muffler in a 3.3L Vanagon...
In stock

$139.95
This cat is 2" inlet and outlet and allows increased exhaust flow compared with the original Vanagon cat. It comes without oxygen sensor ports. One or two...

$150.00
This is the standard stainless steel coolant pipe for our class-leading coolant system.  This part will make any conversion simpler, more reliable and...
In stock
+

$159.00
We searched very long and hard for a muffler that was compact enough to fit in the space in the Vanagon left wheel well, free flowing enough to not lose...
Out of stock

$159.00
This CAN bus to USB interface enables you to connect your PC to the SC ECUs. It comes complete with 2m of wiring to connect to the engine wiring loom and a...
In stock
+

$159.95
Performance muffler This muffler is 2" inlet and and outlet size and offers substantially better flow than the stock Vanagon muffler. It is close to...
In stock
+

$169.95
The Ultra Compact Automotive Computer The ScanGaugeII is an extremely compact automotive computer designed to read and display information about your...
In stock

$169.95
Performance muffler This muffler is 2 1/4" inlet and outlet size and offers substantially better flow than the stock Vanagon muffler. It is close to...
In stock
+

$185.00
NEW - Includes mounting hardware. Automatic Vanagons have a factory installed transmission cooler that uses engine coolant and the radiator to cool...
In stock
+

$185.95
This head gasket set is from a Subaru original equipment manufacturer. Fits the following engines: Subaru Legacy 2.2L 1990-1998 Subaru Impreza 2.2L...
In stock
+

$195.00
Replacement slave cylinder and release bearing for our bellhousing. Metal version, recommended for all version bellhousing. We recommends replacing...
In stock
+